 |
 |
 |
 |
 |
 |
 |
 |
 |
|
 |
||
MODEL GE Gustafson's Model GE is an electrically actuated cross-cut sampler providing convenient and accurate sampling of free-flowing, non-homogeneous commodities, grains, seed and materials in vertical or inclined spouts. USDA, Canadian, FGIS and NOPA approved. A "pelican-type" head with a fixed or adjustable rate of travel moves across the flow of material for a representative, cross-cut sample. 3/4-HP, 115-volt, 1-PH, TENV DC motor with optional 230/460-volt, 3-PH TEFC AC motor and 115-volt, 1-PH DC explosion-proof motors. ?Class 1, Division 1, Group D and Class 2, Division 1, Group E, F & G. |
 |
|
| MODEL L Gustafson's Model L is designed for automatic sampling of liquids and slurries up to 1,000 CPS viscosity in pressure lines and tanks. Available in two sizes with capacities of 10cc?s and100cc?s. Constructed of 316 stainless steel on all contact parts; sample cavity purge fitting is standard. Available with optional heating jacket to maintain sample temperature, and sample container isolation system for hazardous materials. 80 psig air requirements. |
 |
|
|
MODEL MG
Gustafson's Model MG is an automatic strip sampler designed to sample pellets, powders, granules, grain, seed and all free-flowing materials from gravity chutes. Removable stainless steel sample tube for easy clean-up. Electrically operated at 120v AC. For more information about any of the Samplers available at AES, please call us at (215) 627-9556. |
 |
|
|
MODEL PR
Gustafson's Model PR is designed for automatic spot sampling of free-flowing materials in dilute and dense phase horizontal pneumatic transfer lines. The Model PR is also recommended for slurry sampling. Sample tube made of 316 stainless steel, aluminum cast housing, fiberglass filled Teflon seals and 4"bore oilless industrial air cylinder. Operates at 80 psig. |
 |
|
|
MODEL R
Gustafson's Model R is designed for automatic spot sampling of free-flowing and non-free-flowing materials (granules, powders and flakes), high viscosity liquids or slurries from gravity lines and positive or negative pressure systems. Standard fiberglass filled Teflon seals. Close tolerance between sample tube and auger allows product clean-out. Requires 80 psig air pressure and 120v AC. |
 |
|
|
MODEL RB
Gustafson's Model RB is designed for automatic strip sampling of free-flowing and non-free-flowing materials (granules, powders and flakes) in gravity lines, mixers and blenders. Allows product sample to be continuously discharged while sample tube is fully extended. Requires 80 psig air pressure and 120v AC. |
 |
|
|
MODEL RPG
Gustafson's Model RPG is designed for spot sampling of powders, flakes and granules in gravity chutes. Usually recommended where degradation of product must be avoided. Requires 80 psig air pressure. |
 |
|
|
MODEL RX
Gustafson's Model RX is designed for automatic strip sampling of free-flowing powders, granules, pellets, grain and seed from positive or negative, horizontal or vertical dilute phase pneumatic conveying systems and bins or hoppers. Assembled pre-mounted and is exceptionally compact with aluminum housing, 316 stainless steel tube. Teflon seals and vented sample container. Special 90 degree model available for handling fine powders. 80 psig air requirements. |
 |
|
|
MODEL SA-A
Gustafson's Model SA-A is a cross-cut sampler designed to sample fine powders, pellets, granules, flakes, grain, seed and slurries in vertical spouts and chutes. The pivot method of sampling features a top actuator drive, dust-tight housing, neoprene seals and Kevlar braided packing. USDA, Canadian, FGIS and NOPA approved. For more information about any of the Samplers available at AES, please call us at (215) 627-9556. |
 |
|
